電子發(fā)燒友網>電子資料下載>類型>參考設計>AD7730L-微控制器無操作系統(tǒng)驅動程序

AD7730L-微控制器無操作系統(tǒng)驅動程序

2512877 2021-04-22 | pdf | 1.44MB | 次下載 | 2積分

資料介紹

This version (25 Jan 2021 05:41) was approved by Robin Getz.The Previously approved version (25 Jan 2021 05:24) is available.

AD7730L - Microcontroller No-OS Driver

Supported Devices

AD7730L

Evaluation Boards

EVAL-AD7730LEBZ

Overview

The AD7730L is a complete analog front end for weigh-scale and pressure measurement applications. The device accepts low-level signals directly from a transducer and outputs a serial digital word. The input signal is applied to a proprietary programmable gain front end based around an analog modulator. The modulator output is processed by a low pass programmable digital filter, allowing adjustment of filter cutoff, output rate and settling time.

The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for Renesas platforms.

HW Platform(s):

Renesas Demo Kit for RL78G13 (Renesas)
Renesas Demo Kit for RX62N (Renesas)

Driver Description

The driver contains two parts:

The driver for the AD7730L part, which may be used, without modifications, with any microcontroller.
The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver.

The Communication Driver has a standard interface, so the AD7730L driver can be used exactly as it is provided.

There are three functions which are called by the AD7730L driver:

SPI_Init() – initializes the communication peripheral.
SPI_Write() – writes data to the device.
SPI_Read() – reads data from the device.

SPI driver architecture

The following functions are implemented in this version of AD7730L driver:

Function	Description
unsigned char AD7730L_Init(void)	Configures I/O pins from/towards the component and resets the device.
void AD7730L_SoftReset(void)	Resets the device.
void AD7730L_SetRegisterValue(unsigned char registerAddress, unsigned long registerValue, unsigned char bytesNumber)	Writes data into a register.
unsigned long AD7730L_GetRegisterValue(unsigned char registerAddress, unsigned char bytesNumber)	Reads the value of a register.
void AD7730L_WaitForReady(void)	Waits for Ready pin to go low.
void AD7730L_SetMode(unsigned short modeOperation, unsigned char inputRange, unsigned char channel)	Writes the specified mode of operation in Mode Register.
void AD7730L_SetFilterOutputRate(unsigned long outputRate, unsigned char chop, unsigned char skip)	Writes a value corresponding to an output rate in Filter Register.
void AD7730L_Calibrate(unsigned char channel, unsigned char inputRange, unsigned long outputRate, unsigned char dacValue)	Performs a calibration sequence for a channel.
unsigned long AD7730L_SingleRead(unsigned char channel, unsigned char inputRange);	Reads the result of a single conversion.
unsigned long AD7730L_ContinuousReadAvg(unsigned char channel, unsigned char inputRange, unsigned char sampleNumber);	Returns the average of several conversion results.

Downloads

Renesas RL78G13 Quick Start Guide

This section contains a description of the steps required to run the AD7730L demonstration project on a Renesas RL78G13 platform.

Required Software

IAR Embedded Workbench for Renesas RL78 Kickstart
Applilet4 for RL78G13

Hardware Setup

An EVAL-AD7730LEBZ has to be interfaced with the Renesas Demonstration Kit (RDK) for RL78G13:

  EVAL-AD7730LEBZ SKT1 connector Pin 3 (CS)    → YRDKRL78G13 J11 connector Pin 1
  EVAL-AD7730LEBZ SKT1 connector Pin 5 (DIN)   → YRDKRL78G13 J11 connector Pin 2
  EVAL-AD7730LEBZ SKT1 connector Pin 7 (DOUT)  → YRDKRL78G13 J11 connector Pin 3
  EVAL-AD7730LEBZ SKT1 connector Pin 1 (SCLK)  → YRDKRL78G13 J11 connector Pin 4
  EVAL-AD7730LEBZ SKT1 connector Pin 6 (DGND)  → YRDKRL78G13 J11 connector Pin 5
  EVAL-AD7730LEBZ SKT1 connector Pin 2 (RDY)   → YRDKRL78G13 J11 connector Pin 7
  EVAL-AD7730LEBZ SKT1 connector Pin 4 (RESET) → YRDKRL78G13 J11 connector Pin 9
  EVAL-AD7730LEBZ SKT1 connector Pin 9 (SYNC)  → YRDKRL78G13 J11 connector Pin 10

Software Setup

With the Applilet3 for RL78G13 tool the following peripherals have to be configured:

CSI10 (Clocked Serial Interface 10) – For the AD7730L part and the ST7579 LCD

Choose to generate the Transmit/receive function for the CSI10 and configure the interface with the following settings:

Transfer mode setting: Single transfer mode
Data length setting : 8 bits
Transfer direction setting: MSB
Specification of data timing: Type 1
Transfer rate setting – Clock mode: Internal clock (master)
Transfer rate setting – Baudrate: 1000000 (bps)
Interrupt setting – Transfer interrupt priority (INTCSI10): Low
Uncheck the callback functions.

TM00 (Timer 00) – For the DelayMs() function

Configure TM00 as an interval timer:

Interval timer setting - Interval value(16 bits): 1 ms
Interval timer setting - Uncheck Generates INTM00 when counting is started
Interrupt setting - Uncheck End of timer channel 0 count, generate an interrupt (INTM00)

Watchdog Timer

Disable the watchdog timer:

Choose for the Watchdog timer operation setting: Unused option.

Reference Project Overview

The reference project initializes the device, calibrates it and performs single and continuous reads of an analog signal. The results are displayed on the LCD.

Software Project Setup

This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RL78G13 for controlling and monitoring the operation of the ADI part.

Two software applications have to be used: Applilet3 for RL78G13 (a tool that automatically generates device drivers for MCU peripheral functions) and IAR Embedded Workbench for Renesas RL78 (the integrated development environment).

Step 1 - Applilet3 for RL78G13

Run the Applilet3 for RL78G13 tool and create a new project for R5F100LE processor. Select IAR Compiler build tool, a project name, a location for the new project and press OK.

Keep the default Pin assignment setting and click Fix settings.

Now the desired peripherals can be configured and the code can be generated. For example, if the clocked serial interface 10 (CSI10) has to be configured, select the Serial peripheral, choose for the Channel 2 of Serial Array Unit 0 (SAU0) the CSI10 interface, Transmit/receive function option and then go to CSI10 tab.

To configure the CSI10 interface for serial transmissions of 8 bits, with MSB first, with the data captured on clock's rising edge, with a frequency of the clock of 1 MHz and the idle state high, the settings from the following image have to be made.

After all the desired peripherals are configured click on the Generate Code button and a new workspace and a new project for the IAR Embedded Workbench will be generated. After the code was generated close the Applilet3 for RL78G13 tool.

Step 2 - IAR Embedded Workbench for Renesas RL78

Run the IAR Embedded Workbench and open the workspace created with the Applilet3 tool.

Copy the files extracted from the zip file into the user_src folder, located in the project’s folder.

The new source files have to be included into the project. Add in the user_src group the files from the corresponding folder (Right click on the group and select Add – Add Files…). Because a new Main file was included the r_main.c file from the applilet_src group has to be deleted (Right click on the file and select Remove).

Now the debugger driver has to be selected from the project’s options. Right click on the project name and select Options. From the Debugger category choose the TK Debugger Driver.

Now, the project is ready to be compiled and downloaded on the board. Press the F7 key to compile it. Press CTRL + D to download and debug the project.

29 Feb 2012 17:01 · Dragos Bogdan